MAYTAG
Gemini Range/Stove/Oven Fault Codes


Failure Code Condition Check/Repair
 
F0:-0 None
 
F1:-1 Runaway Cook.
1.   Upper oven Check oven temperature sensor, replace if necessary.
 
F1:-2 Runaway Cook.
1.    Lower oven Check oven temperature sensor, replace if necessary.
 
F1:-3 Runaway Clean.
1.    Upper oven Check oven temperature sensor, replace if necessary.
 
F1:-4 Runaway Clean.
1.    Lower oven Check oven temperature sensor, replace if necessary.
 
F1:-5 Keypad Cancel.
1.   Upper Check keypad, replace if necessary.
 
F1:-6 Keypad Cancel.
1.    Lower Check keypad, replace if necessary.
 
F1:-7 Keypad Disconnected.
1.   Check wiring between keypad and Electronic Range Control (ERC).
 
F1:-8 Keypad Shorted.
1.   Check to see if steam or other moisture is getting into clock assembly.
2.    Replace keypad if necessary.
 
F1:-9 Slave
 
F1:-A Latch Switch Upper.
1.   Check door latch switches.
2.   Replace if necessary.
 
F1:-B Latch Switch Lower.
1.    Check door latch switches.
2.    Replace if necessary.
 
F1:-C Door Switch Upper.
1.   Check door switch.
2.   Replace if necessary.

F1:-D Door Switch Lower.
1.   Check door switch.
2.   Replace if necessary.
 
F1:-E EEPROM Control.
1.   Replace Electronic Range Control (ERC).
 
F1:-F Jumper  Control
 
F1:-H EEPROM  Read Control.
1.    Replace Electronic Range Control (ERC).
 
F1:-L Oven temperature sensor Track Control.
1.   Check oven temperature sensor.
2.   Replace if necessary.
 
F3:-2 Oven temperature sensor Lower oven.
1.   Check oven temperature sensor.
2.   Replace if necessary.
 
F3:-1 Oven temperature sensor Upper oven.
1.   Check oven temperature sensor.
2.   Replace if necessary.

F9:-1 Latch Lock Upper Oven.
1.   Check for obstruction in door lock mechanism.
 
F9:-2 Latch, Unlock Upper Oven.
1.   Check for obstruction in door lock mechanism.
 
F9:-3 Latch Both Upper Oven
1.   Check for obstruction in door lock mechanism.
 
F9:-4 Latch Lock Lower Oven.
1.   Check for obstruction in door lock mechanism.
 
F9:-5 Latch Unlock Lower Oven.
1.   Check for obstruction in door lock mechanism.
 
F9:-6 Latch Both Lower.
1.   Check for obstruction in door lock mechanism.
 

MAYTAG
Type "C" and "D" Clocks Range/Stove/Oven Fault Codes

 
Failure Code Condition Check/Repair
 
F1  Supervisory relay enable shorted (non-cook mode); sounds alarm and inhibits cook mode if alarm fault monitor is always active in non-cook mode, and requires removal of power until serviced.
1.  Usually a bad touch pad or clock assembly (also called the ERC).
2.  Replace touchpad or ERC.
 
F2  Bake/broil/clean temp runaway alarm; sounds alarm and resets control to non-cook mode when bake/broil/clean temp exceeds programmed limits.
1.   Usually means a stuck relay. Electric @ 525F (bake), 640F(broil), 900F(clean)   Gas @ 525F (bake), 640F(broil), 900F(clean).
 
F3  Open temp oven temperature sensor; sounds alarm and inhibits cook mode.
1.   Replace oven temperature sensor.
 
F4  Shorted temp oven temperature sensor; sounds alarm and inhibits cook mode.
1.   Replace oven temperature sensor.
 
F5  Supervisory relay enable open (cook mode); sounds alarm and resets the control to non-cook mode.
1.   Replace electronic range control (ERC).
 
F5 Missing A/C line cycle detector.
1.   Displays code (no audible).
2.   Unplug appliance for two minutes, should clear problem.
 
F7 Function key shorted.
1.  Too hot at the clock assembly (also called the ERC).
2.  Shorted touch pad.
3.  Clock assembly (also called the ERC).
4.  Replace touchpad or ERC.
 
F8  Analog/Digital supervisory; sounds alarm to non-cook mode.
1.   Replace ERC.
 
F9  Door latch supervisory (door latched).
1.   Unlock door and check switches
2.   Check clock assembly (also called the ERC).
 
F0  Cancel key supervision.
1.   Requires the removal of power until serviced. See qualified technician.
 

 
MAYTAG
Range/Stove/Oven Fault Codes


Failure Code Condition Check/Repair

F1  Defective touch pad or membrane.
1.   Replace touch pad or membrane (usually the touch pad).
 
F1  Watchdog on board.
1.   Replace touch pad.
2.   Or clock assembly (also called the ERC).
 
F2  Oven too hot.
1.   Replace relay board (if present).
2.   Or bad oven temperature sensor.
 
F3 or F4 Open or shorted oven temperature sensor.
1.   Replace oven temperature sensor.
 
F5  Hardware and watchdog circuits disagree.
1.   Replace clock assembly (also called the ERC).
 
F6  Missing AC signal.
1.   Check for proper voltage.
 
F7  Function key shorted or stuck button.
1.   Replace touch pad or clock assembly (also called the ERC).
2.   Or try to free stuck button.
 
F8  Analog/Digital supervisory.
1.   Replace clock assembly (also called the ERC).
 
F9   Door latch supervisory.
1.   Check door lock circuit.
2.   Or replace clock assembly (also called the ERC).
 
F0  Function key stuck.
1.   Replace touch pad or clock assembly (also called the ERC).

* Here is a simple test that you can do to determine whether the clock or the touchpad are defective when the display reads F1:

1.  Disconnect power to the range.
2.  Gain access to the back of the ERC or "clock").
3.  Unplug the touch pad ribbon connector from the ERC. This will be a flat wire about 1 ½" to 2" wide.
4.  Make sure everything is clear and will not short out when power is turned back on.
5.   Replace any covers removed to gain access to the ERC.
6.  Turn the power back on to the range.
7.  Watch for the F-1 and listen for the beep.
8.  If you get the F-1 and beep, replace the ERC.
9.  If after approximately 60 Minutes you do not get the F-1 fault, replace the touch pad.

NOTE: Some models incorporate the touch pad and the clock control as one part so F1 would mean you would have to replace the clock/timer control.

Warning: If you do not feel comfortable doing this test or making this repair please contact a qualified appliance repair technician.
 

MAYTAG
Stackable A/W and Dryer Fault Codes


Failure Code Condition Check/Repair
 
"L" persists in washer display Lid lock failure.
1.   Replace switch, linkage, lock solenoid or control board.
 
1E  persists in washer display Lid lock failure.
1.   Replace lid lock switch or control board.
 
9E  appears in dryer display Door switch failure.
1.   Check door switch wiring.
2.   Or door switch,
3.   Or control board.
 
"U" occurs for no reason in display.
1.   Unbalanced load.
2.   Unbalance switch.
3    Or control board.
 
6E  appears in dryer display.
1.   Temp control error,
2.   Ambient (room) temperature too cool,
3   Or thermistor,
4   Wire harness,
5   Control board.
 
7E  appears in dryer display.
1.   Temp control error - overheating Check:
2.   Venting for restriction,
3.   Thermistor,
4.   Control board,
5.   Cycling thermostat (regular).
 
8E  appears in dryer display.
1.   Motor relay circuit Check:
2.   Relay coil,
3.   Wire harness or,
4.   Control board.

maytag fault codes


Call (918) 488-1320

   *OPEN 7 DAYS*