*OPEN 7 DAYS*

WHIRLPOOL
Range/Stove/Oven Fault Codes Non Y-Line

Failure Code Condition Check/Repair

NOTE: Not valid for Y line. If there is a Y near the end of your model number, do not use this chart.

4 Digit Failure Code
 
F0 - E0 Analog to Digital Failure Disconnect for 30 seconds - if display re-appears - replace control
F1 - E1 Safety flip flop Replace Electronic Range Control/Clock (ERC)
F2 - E0 Shorted keypad Replace Electronic Range Control/Clock (ERC)
F3 - E0 Oven temperature sensor or oven temperature sensor fuse opened Replace oven temperature sensor or fuse
F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor
F3 - E2 Oven too hot Replace oven temperature sensor
F3 - E3 Clean temp too hot Replace oven temperature sensor
F5 - E0 F5 - E1 and E2 Check door/latch switch Replace component
2 Digit Failure Code
F0 or F1 or F5 Failed transistor Replace Electronic Range Control/Clock (ERC)
F2 - E0 Oven temp too high 1. Test operation of door lock on self-clean models
2. Test relay contact operation
3. High resistance in oven temperature sensor
F3 Open oven temperature sensor or thermal fuse Replace oven temperature sensor or thermal fuse
F4 Shorted oven temperature sensor Replace oven temperature sensor
F6 Problem in time keeping circuit 1. Reset time and/or cooking operation
2. Check for proper ground
F7 Stuck function switch or button on Electronic Range Control (ERC) Replace ERC (Electronic Range Control/Clock)
F8 Failure Electronic Range Control (ERC) Replace ERC (Electronic Range Control/Clock)
F9 Door lock circuit Check wiring and test operation of door lock switch
 
 
WHIRLPOOL
Range/Stove Oven Fault Codes, Common


Failure Code Condition Check/Repair
 
2 Digit Failure Code

F1 Analog to Digital Failure Disconnect for 30 seconds - if display reappears - replace control board
F1 Safety flip flop Replace board
F1 Shorted keypad Replace keypad
F3 Oven temperature sensor opened Replace oven temperature sensor
F2 Oven temperature sensor shorted Replace oven temperature sensor
F3 Oven too hot Replace oven temperature sensor
F3 Clean temp too hot Replace oven temperature sensor
F5 Check door/latch switch Replace switch if defective
4 Digit Failure Code
F1 - E1 Safety flip flop Replace board
F2 - E0 Shorted keypad Replace keypad
F3 - E0 Oven temperature sensor opened Replace oven temperature sensor
F3 - E1 Oven temperature sensor shorted Replace oven temperature sensor
F3 - E2 Oven too hot Replace oven temperature sensor
F3 - E3 Clean temp too hot Replace oven temperature sensor
F5 - E0 F5 - E1 and E2 Check door/latch switch Replace switch if defective
 
WHIRLPOOL
Range/Stove Oven 30" Free-standing, Models SF3…& 24" Built-In


Failure Code Condition Check/Repair
 
F2 Oven temperature above specifications 8-pin connector oven temperature sensor to the Electronic Range Control (ERC)
F3 Open oven temperature sensor Check wiring harness, replace oven temperature sensor if necessary
F4 Shorted oven temperature sensor Check wiring harness, replace oven temperature sensor if necessary
F5 Pushbutton stuck Check for binding of pushbuttons and control panel glass. If OK, replace touch panel
F6 Computer logic interrupted (timing) Replace Electronic Range Control (ERC)
F7 Computer logic interrupted (lock motor) Replace Electronic Range Control (ERC)
F8 Computer logic interrupted Replace Electronic Range Control (ERC)

WHIRLPOOL
Calypso Washing Machine


Failure Code Condition Check/Repair

PF Power Failure PF flashes if the washer loses power during a running cycle. The washer does not flash PF when it is first plugged in.

Press START to continue the cycle from the moment that power was lost -OR-

Press STOP/CANCEL to clear the display and completely cancel the cycle.
FL Flood Condition FL flashes if any overfill condition occurs. This condition occurs when excessive water in the tub causes the overfill switch to trip. The control must realize that the trip was due to an overfill condition instead of a suds lack condition in order for FL to be displayed

With an overfill condition, the beeper repeats a warning every 10 seconds with no time-out. The pump is cycled in drain mode for 30 seconds on, 30 seconds off until the overfill switch resets or power is discontinued to the unit.

Press STOP/CANCEL to clear the display.
Er Processor Reset Error This error code is displayed if the control failed to save cycle information during a power failure. This does not generate an error code beep.

Press STOP/CANCEL to clear the display.
LF Long Fill If the water fill time exceeds ten minutes, the water valves are turned off and LF is flashed.

Press STOP/CANCEL to clear the display.
CE Communications Error If there is any breakdown in communication between the machine controller and the motor controller, CE flashes and the unit beeps once.

Some common causes of CE errors include:

· Conformal coating on serial communications pins between the machine controller and motor controller. After disconnecting power to the unit, try scraping this coating off the pins.

· Check the resistance values between the serial communications pins with the connectors in place. Make sure the harness does not have a bad connection.

· Check the quick disconnect at the motor terminal. The drive motor must be hooked up properly or a CE error will occur.

· Drive motor thermal protector has opened.

·Motor controller is not powered or fuse has opened. Replace motor controller.

Press STOP/CANCEL to clear the display.
Ld Long Drain Ld flashes if it takes longer than 5 minutes to pump out water to a point where the operating pressure switch resets.

Press STOP/CANCEL to clear the display.
CA
Cl Average current limit Or
Instantaneous current limit If a status signal comes back from the motor controller that a current limit has been breached, the unit will return to standby mode and display either CA for average current limit trip or Cl for instantaneous current limit trip.

Average current trip occurs if there is a 2 second average of current draw greater than 5.55 amps at the motor windings.

Instantaneous current trip occurs if there is a spike of 26 amps instantly at the motor windings.

This may signify problems with the drive motor, thermal protector, or motor controller. Over-loading the unit may cause this problem.

Press STOP/CANCEL to clear the display
ob Off Balance If the motor controller detects an unrecoverable off-balance condition, the machine controller will shut down and display an ob for Off Balance

The lid switch must be opened at least once before restarting the cycle, if this condition occurs. Opening the lid will allow the customer to view and redistribute the load.

Press STOP/CANCEL to clear the display.
Sr Stuck Relay Sr signifies a failure of the relay in the closed position. With this failure, power to the motor controller cannot be turned off by the machine controller.

The machine control board may have a bad relay and may need to be replaced. Check pins 1 and 5 of P16 of the machine controller and pins 1 and 2 of P1 of the motor controller. This should have AC line voltage when the motor controller is powered.

Press STOP/CANCEL to clear the display.
LS Lid Switch Error The control should flash this error code if it cannot detect the lid switch opening and closing properly. This error code may also be used if there is a disagreement between the motor and machine controllers on the stat if the lid switch. The control should not allow the unit to run in this condition.

This code will also appear if the user presses the START key while the lid is open.

Open the lid or press STOP/CANCEL to clear the display.
 

WHIRLPOOL
Calypso Matching Dryer

 
Failure Code Condition Check/Repair
 
PF Power Failure If the household power goes off and the control board was in RUN mode or PAUSE mode, the electronic control board will display a power failure error code.
E1 or E2 Thermistor Failure The dryer will not operate if the exhaust temperature drops below 18 degrees F. or exceeds 250 degrees F.

When the thermistor circuit is open (>50K ohms), the error code E1 flashes in the display.

When the thermistor circuit is shorted (<500 ohms), the error code E2 flashes in the display.

Normal thermistor resistance values:
60 degrees F. - 15.3K ohms.
70 degrees F. - 11.9K ohms.
80 degrees F. - 9.2K ohms.
E3 Touchpad or Software mismatch Flashes when there is a touchpad or software mismatch. NOTE: This error code is displayed only in diagnostics mode.

whirlpool fault codes


Call (918) 488-1320